CNC Laser diode
"12W laser"
Laser diode - wiki - Common wavelengths
professional 1064nm dpss laser module fiber coupled laser diode module
6w-10w 975nm diode infrared laser module 5 watt led diode
5w diode laser cutting mechine test
DIY Homemade laser diode driver
home made co2 laser 40w wing balsa cut. cnc usbcnc planetcnc mk1
Trying to Cut Glass With Laser - 2.5w Blue Module
Cutting and engraving real glass with cheap Chinese laser
TTL-controlled Laser Diode Driver. Updated schematics
Diode Pumped High Peak Power Quasi Q-Switched and Passively Q-Switched Nd:YVO4 Lasers at 1064 nm and 532 nm Using Cr:YAG and KTP Crystals
Diode Pumped Solid State Lasers
Solid State Lasers
450nm 3000mW Focusable blue laser module/Blue Laser Module/TTL
2pcs Nichia NDV4313 120mW 405nm Laser LD Diode Cut Pin TO18 5 6mm SEALED Used
Co2 Laser Engraving Cutting Cutter Head Focus Diode Module Red Dot Positioning DIY CNC Engraver Cutter Part DC 5V
300mW Woodworking Machinery Tools Router Laser Cutting Machine Accessories Laser Diode Laser Tube Laser Cutting Machine NEJE
Engineering Radio Control Aircraft Structures for Light Weight, Strength and Rigidity
Introduction to Building a Model Aircraft Wing
Designing a Lightweight Model Airplane
Fuselage Design
Tail and Flying Surface Design
Engineering Choices
Heavy models are almost always poorly engineered. A well engineered model can still end up heavy due to poor material and equipment selection or poor building techniques. Even so, a properly engineered model at least gives you a fighting chance. A poorly engineered model is usually a lost cause unless you take it back to the drawing board and redesign the entire model.Poor engineering usually is due to one or more of the following:
-
The designer doesn't understand model aircraft structures and over-designs.The designer copies poor engineering concepts of other bad designers or he comes up with all new poor concepts of his own.
-
The design is compromised to ease building at the expense of additional weight.
-
Poor strength-to-weight materials are used to decrease costs to the manufacturer. Additional cheap and heavy material is added to compensate for lack of strength which in turn adds more weight.
Builders have become so lazy over the years that any time they discuss a model having built-up fuselage sides, the kit is called a builder's kit meaning that the kit is only for "true builders." Call it what you want, but one fact will never change — lighter models fly better.
If you aren't willing to do the work to build a lightweight aircraft then don't be surprised when your models don't fly as well as those built by builders who are willing to make the effort.
What I can't figure out is how the new generation of 3D models that have just a handful of ribs having large cut-outs and a profile fuselage weighs as much or more than a "real" airplane that I build that has 20+ ribs in a larger wing. Actually I do know why and here's a clue. Contest balsa ribs don't weigh anything. You could put 50 of them in a wing and it wouldn't make but (at most) an ounce of difference in the finished weight.
The lack of ribs in 3D aircraft is only to give the illusion of light weight. More ribs make a more durable wing having a more accurate airfoil. You get all of this at no weight penalty.
To counter this supposedly lightweight wing, the designers take a thick (heavy) slab of balsa, slap on some plywood (heavier) around the nose and call it a fuselage. So much for the weight savings of having only 4 ribs in the wing!
And by the way, take a look at the size of the leading edge and spars on some of these 3D planks. They are much larger and heavier than what is normally used on more traditional wings. Heavy spars weigh more than light ribs.
CNC wood cutting and laser engraving services
CNC wood cutting and laser engraving ideas
Pinterest - laser engraving
neDPSS laser (red či blue)
Parametry laserových diod a jejich měření
Pro běžné využití stačí změření výstupního výkonu na PWM s tolerancí <±5%
400mW RGY = 290mW
100mW G = 60mW
--
minimální výkon udávaný v specifikaci, RGY měl guaranteed 300mW, čekal jsem 400mW
a dostal jsem 290mW ... :o
---
100mW/532nm a realita 20mW
Časté otázky k laserům
www.laserforum.cz
Profi měření výkonu a energie laserů
www.netlas.eu/slu-by/laser/meranie-v-konu
Žádné komentáře:
Okomentovat